Furuno FA-100 Manual de usuario

PRINTED IN JAPANUAIS TRANSPONDERFA-100Back

4 • When coaxial cable RG-10U/Y (shipyard supply) is used, attach the coaxial plug M-P-7 (dockyard supply) as shown

5How to attach the plug M-P-7 Lay the coaxial cable and attach an M-type plug (if necessary) to the cable as follows. 1. Remove the sheath by 30

6 Mounting procedures 1. Dismount the bottom cover, cut the cable-tie inside the unit and take out the coaxial connector attached to the combined bo

7StanchionThetopofthestanchioncomeintocontactwiththeflange. Installing distributor unit DB-1 The length of the cable between the distributo

81.2 Transponder Unit The transponder unit can be installed on a desktop or flush mounted in a panel. Install it on the chart table or near the steer

9Flush mounting Optional flush mount kit A or B is required for flush mounting. For mounting dimensions, refer to the outline drawing at the back of

101.3 Junction Box Mount the junction box where the junction box is protected from rain and water splash. Mounting 1. Open the lid of the junction

111.4 Power Supply (option) The length of the power cable between the power supply and the transponder unit is 3.5 m. Keep this length in mind when s

12 2. WIRING Connect the equipment, referring to the interconnection diagram at the back this manual. AD-10 INEXTRA I/OGPS AntennaGPA-017SGSC-001PCA

13ConductorS = 1.5 mmφ = 1.56 mm2DPYC-1.5ArmorSheathφ = 11.7 mm***: Waterproofing connectors**: DPYC-1.5, TTYCS-1Q and TTYCS-4 are Japan Industry St

The paper used in this manualis elemental chlorine free.FURUNO Authorized Distributor/DealerFURUNO Authorized Distributor/Dealer9-52 Ashihara-cho,9-52

14Cable Connection at Junction Box Cable fabrication Armor SheathShieldClampherebycableclamp.5to6mm30 Connection Procedure1. Insert driver fro

153. INPUT/OUTPUT SIGNAL 3.1 Inputs from Sensors There are three input ports (SENSOR 1, 2 and 3) which are based on the IEC 61162-1/2. The protocol

16 3.2 Input/Output of AIS Signal Three input/output ports are provided for RS-422 protocol, based on the IEC 61162-1/2. Data transmission rate is s

173.3 Input of Gyrocompass Signal If the gyrocompass has no HDT signal, the AD-10 format (FURUNO format) signal can be input via the FURUNO A/D Co

18 3.5 LAN Input/Output The FA-100 supports Ethernet based on LAN. Its protocol is 10BASE-T and the transmission rate is 10 Mbps. To connect the FA-1

193.7 Jumper Setting in the Junction Box Each RS-422 RX line (on the PCB 24P0031 in the junction box) has a jumper block with 240 ohms termination r

20 3.8 Input/Output Sentences 1) SENSOR 1, SENSOR2, and SENSOR3 ports These ports can receive IEC61162-1/2 standard data. The transmission rate of

213.9 Changing Ship’s Mains Specifications The power supply PR-240-CE is shipped ready for connection to a 200-230 VAC ship’s mains. If the ship’s m

22 4. SETTING AND ADJUSTMENT After installing the equipment, set up the own ship’s static information (MMSI, IMO number, ship’s name, call sign, t

239. Enter ship’s name, using up to 20 alphanumeric characters. To switch between alphabet and numerical character, press the [SFT] key. To enter an

i SAFETY INSTRUCTIONSWARNINGTurn off the power at the switchboardbefore beginning the installation.Fire or electrical shock can result if thepower is

24 4.2 Setting GPS Antenna Position and Ship’s Type 1. In the INIT SETTING sub-menu, press the [6] key to open the SET ANTENNA POS window. SET AN

257. Press the [NEXT] key to select TYPE NO. Confirm type of ship with ship’s captain before setting it. 8. Press the [2], [4], [6] or [8] key as a

26 10. Press the [MENU] key. The SAVE confirmation window appears. SAVE ? YES NO CANCEL SAVE confirmation window 11. With YES selected, pres

275. Select the appropriate data transmission rate from 4800 bps and 38.4 kbps for PC I/O, SNSR 1, SNSR 2, SNSR 3, LR, BCON (beacon receiver), EXTRA

2812. Set L/L position, COG and SOG data priority with the numeric keys according to sensors connected. COG: Course over ground SOG: Speed over g

2920. Press [4] key to display the SET LAN (IP ADRS) window. [SET LAN (IP ADRS)] IP ADDRESS:000-000-000-000 SUB NET MASK:000-000-000-000 POR

This page is intentionally left blank.

ＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴ24AA-X-9854 -1 FA-100-J/E,FA-100-J/E-HKFA-100-J/E,FA-100-J/E-HKFA-100-J/E,FA-100-J/E-HKFA-100-J/E,FA-1

ＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴ24AA-X-9851 -4 CB-100-A､CB-100-A-HKCB-100-A､CB-100-A-HKCB-100-A､CB-100-A-HKCB-100-A､CB-100-A-HKN A M E

ＰＡＣＫＩＮＧ ＬＩＳＴ24AA-X-9853 -3 GVA-100N A M EO U T L I N EDESCRIPTION/CODE №Q'TY1/1ユニット UNIT複合空中線部GPS/VHF COMBINED ANTENNAGVA-100000-053-8101工事材料 INS

ii TABLE OF CONTENTS SYSTEM CONFIGURATION... iii EQUIPMENT LISTS ...

CODE NO.CODE NO.CODE NO.CODE NO.004-365-780TYPETYPETYPETYPECP20-01111略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALL

ＰＡＣＫＩＮＧ　ＬＩＳＴＰＡＣＫＩＮＧ　ＬＩＳＴＰＡＣＫＩＮＧ　ＬＩＳＴＰＡＣＫＩＮＧ　ＬＩＳＴ24AA-X-9852 -5 PR-240-CEPR-240-CEPR-240-CEPR-240-CEN A M EO U T L I N EDESCRIPTION/CODE №Q'TY1/1ユ

CODE NO.CODE NO.CODE NO.CODE NO.TYPETYPETYPETYPE略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALLATION MATERIALS工事材料表工

CODE NO.CODE NO.CODE NO.CODE NO.004-372-420TYPETYPETYPETYPECP20-01701略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALL

CODE NO.CODE NO.CODE NO.CODE NO.004-365-780TYPETYPETYPETYPECP20-01111略  図OUTLINE名  称 NAME数量Q'TY用途／備考REMARKS番 号 NO. 型名／規格DESCRIPTIONS1/1-1 INSTALL

Oct. 21,'02D - 2

Oct. 21,'02D - 3

Sep.29'05D-4

May 20 '03D-4a

iiiSYSTEM CONFIGURATION : Standard : Option GPS/VHFcombined antennaGVA-100GPS antennaGPA-017SGSC-001Distributor unitDB-1VHF whip antennaTransponder

Feb.22'05D-5

Jan. 9,'03D - 6

Jan. 9, '03D - 7

Mar.11'04H.HayashiD-8

Feb.02'05D-9

Nov.28'03D-10

Y. HataiD-11

Oct.02'03D-12

3412 56TYPE名前NAMEkgDWG. No.SCALEAPPROVEDDRAWNCHECKEDMASSFA-100国際船舶自動識別装置相互結線図INTERCONNECTION DIAGRAMU-AIS TRANSPONDERCBDA1234IEC61162-1/2FA-100J2GPS-A

iv EQUIPMENT LISTS Standard supply No. Name Type Code no. Qty Remarks 1 Transponder Unit FA-100 - 1 2 Junction Box CB-100 - 1 GPS Antenna G

11. MOUNTING 1.1 Antenna Unit 1.1.1 GPS antenna unit Install the GPS antenna unit referring to the drawing at the back of this manual D-1. When sele

2How to attach the connector N-P-8DFB for cable 8D-FB-CV Outer SheathArmorDimensions in millimeters.Inner Sheath ShieldRemove outer sheath and armor

31.1.2 VHF antenna Location Location of the mandatory AIS VHF-antenna should be carefully considered. Digital communication is more sensitive than